Thanks for all the likes, good words and support you gave us in the first two part of this article. In the first article we discussed commands for those users who have just switched to Linux and needed the necessary knowledge to start with.
- 20 Useful Commands for Linux Newbies
In the second article we discussed the commands which a middle level user requires to manage his own system.
- 20 Advanced Commands for Middle Level Linux Users
What Next? In this article I will be explaining those commands required for administrating the Linux Server.
Linux Expert Commands
41. Command: ifconfig
ifconfig is used to configure the kernel-resident network interfaces. It is used at boot time to set up interfaces as necessary. After that, it is usually only needed when debugging or when system tuning is needed.
Check Active Network Interfaces
[[email protected] ~]$ ifconfig
eth0 Link encap:Ethernet HWaddr 40:2C:F4:EA:CF:0E
inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::422c:f4ff:feea:cf0e/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:163843 errors:0 dropped:0 overruns:0 frame:0
TX packets:124990 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:154389832 (147.2 MiB) TX bytes:65085817 (62.0 MiB)
Interrupt:20 Memory:f7100000-f7120000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:78 errors:0 dropped:0 overruns:0 frame:0
TX packets:78 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4186 (4.0 KiB) TX bytes:4186 (4.0 KiB)
Check All Network Interfaces
Display details of All interfaces including disabled interfaces using “-a” argument.
[[email protected] ~]$ ifconfig -a
eth0 Link encap:Ethernet HWaddr 40:2C:F4:EA:CF:0E
inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::422c:f4ff:feea:cf0e/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:163843 errors:0 dropped:0 overruns:0 frame:0
TX packets:124990 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:154389832 (147.2 MiB) TX bytes:65085817 (62.0 MiB)
Interrupt:20 Memory:f7100000-f7120000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:78 errors:0 dropped:0 overruns:0 frame:0
TX packets:78 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4186 (4.0 KiB) TX bytes:4186 (4.0 KiB)
virbr0 Link encap:Ethernet HWaddr 0e:30:a3:3a:bf:03
inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Disable an Interface
[[email protected] ~]$ ifconfig eth0 down
Enable an Interface
[[email protected] ~]$ ifconfig eth0 up
Assign IP Address to an Interface
Assign “192.168.1.12” as the IP address for the interface eth0.
[[email protected] ~]$ ifconfig eth0 192.168.1.12
Change Subnet Mask of Interface eth0
[[email protected] ~]$ ifconfig eth0 netmask 255.255.255.
Change Broadcast Address of Interface eth0
[[email protected] ~]$ ifconfig eth0 broadcast 192.168.1.255
Assign IP Address, Netmask and Broadcast to Interface eth0
[[email protected] ~]$ ifconfig eth0 192.168.1.12 netmask 255.255.255.0 broadcast 192.168.1.255
Note: If using a wireless network you need to use command “iwconfig“. For more “ifconfig” command examples and usage, read 15 Useful “ifconfig” Commands.
42. Command: netstat
netstat command displays various network related information such as network connections, routing tables, interface statistics, masquerade connections, multicast memberships etc..,
List All Network Ports
[[email protected] ~]$ netstat -a Active UNIX domain sockets (servers and established) Proto RefCnt Flags Type State I-Node Path unix 2 [ ACC ] STREAM LISTENING 741379 /run/user/user1/keyring-I5cn1c/gpg unix 2 [ ACC ] STREAM LISTENING 8965 /var/run/acpid.socket unix 2 [ ACC ] STREAM LISTENING 18584 /tmp/.X11-unix/X0 unix 2 [ ACC ] STREAM LISTENING 741385 /run/user/user1/keyring-I5cn1c/ssh unix 2 [ ACC ] STREAM LISTENING 741387 /run/user/user1/keyring-I5cn1c/pkcs11 unix 2 [ ACC ] STREAM LISTENING 20242 @/tmp/dbus-ghtTjuPN46 unix 2 [ ACC ] STREAM LISTENING 13332 /var/run/samba/winbindd_privileged/pipe unix 2 [ ACC ] STREAM LISTENING 13331 /tmp/.winbindd/pipe unix 2 [ ACC ] STREAM LISTENING 11030 /var/run/mysqld/mysqld.sock unix 2 [ ACC ] STREAM LISTENING 19308 /tmp/ssh-qnZadSgJAbqd/agent.3221 unix 2 [ ACC ] STREAM LISTENING 436781 /tmp/HotShots unix 2 [ ACC ] STREAM LISTENING 46110 /run/user/ravisaive/pulse/native unix 2 [ ACC ] STREAM LISTENING 19310 /tmp/gpg-zfE9YT/S.gpg-agent ....
List All TCP Ports
[[email protected] ~]$ netstat -at Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 localhost:mysql *:* LISTEN tcp 0 0 *:5901 *:* LISTEN tcp 0 0 *:5902 *:* LISTEN tcp 0 0 *:x11-1 *:* LISTEN tcp 0 0 *:x11-2 *:* LISTEN tcp 0 0 *:5938 *:* LISTEN tcp 0 0 localhost:5940 *:* LISTEN tcp 0 0 ravisaive-OptiPl:domain *:* LISTEN tcp 0 0 ravisaive-OptiPl:domain *:* LISTEN tcp 0 0 localhost:ipp *:* LISTEN tcp 0 0 ravisaive-OptiPle:48270 ec2-23-21-236-70.c:http ESTABLISHED tcp 0 0 ravisaive-OptiPle:48272 ec2-23-21-236-70.c:http TIME_WAIT tcp 0 0 ravisaive-OptiPle:48421 bom03s01-in-f22.1:https ESTABLISHED tcp 0 0 ravisaive-OptiPle:48269 ec2-23-21-236-70.c:http ESTABLISHED tcp 0 0 ravisaive-OptiPle:39084 channel-ecmp-06-f:https ESTABLISHED ...
Show Statistics for All Ports
[[email protected] ~]$ netstat -s
Ip:
4994239 total packets received
0 forwarded
0 incoming packets discarded
4165741 incoming packets delivered
3248924 requests sent out
8 outgoing packets dropped
Icmp:
29460 ICMP messages received
566 input ICMP message failed.
ICMP input histogram:
destination unreachable: 98
redirects: 29362
2918 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 2918
IcmpMsg:
InType3: 98
InType5: 29362
OutType3: 2918
Tcp:
94533 active connections openings
23 passive connection openings
5870 failed connection attempts
7194 connection resets received
....
OK! For some reason if you want not to resolve host, port and user name as a output of netstat.
[[email protected] ~]$ netstat -an
Fine, you may need to get the output of netstat continuously till interrupt instruction is passed (ctrl+c).
[[email protected] ~]$ netstat -c
For more “netstat” command examples and usage, see the article 20 Netstat Command Examples.
43. Command: nslookup
A network utility program used to obtain information about Internet servers. As its name suggests, the utility finds name server information for domains by querying DNS.
[[email protected] ~]$ nslookup tecmint.com Server: 192.168.1.1 Address: 192.168.1.1#53 Non-authoritative answer: Name: tecmint.com Address: 50.16.67.239
Query Mail Exchanger Record
[[email protected] ~]$ nslookup -query=mx tecmint.com Server: 192.168.1.1 Address: 192.168.1.1#53 Non-authoritative answer: tecmint.com mail exchanger = 0 smtp.secureserver.net. tecmint.com mail exchanger = 10 mailstore1.secureserver.net. Authoritative answers can be found from:
Query Name Server
[[email protected] ~]$ nslookup -type=ns tecmint.com Server: 192.168.1.1 Address: 192.168.1.1#53 Non-authoritative answer: tecmint.com nameserver = ns3404.com. tecmint.com nameserver = ns3403.com. Authoritative answers can be found from:
Query DNS Record
[[email protected] ~]$ nslookup -type=any tecmint.com Server: 192.168.1.1 Address: 192.168.1.1#53 Non-authoritative answer: tecmint.com mail exchanger = 10 mailstore1.secureserver.net. tecmint.com mail exchanger = 0 smtp.secureserver.net. tecmint.com nameserver = ns06.domaincontrol.com. tecmint.com nameserver = ns3404.com. tecmint.com nameserver = ns3403.com. tecmint.com nameserver = ns05.domaincontrol.com. Authoritative answers can be found from:
Query Start of Authority
[[email protected] ~]$ nslookup -type=soa tecmint.com Server: 192.168.1.1 Address: 192.168.1.1#53 Non-authoritative answer: tecmint.com origin = ns3403.hostgator.com mail addr = dnsadmin.gator1702.hostgator.com serial = 2012081102 refresh = 86400 retry = 7200 expire = 3600000 minimum = 86400 Authoritative answers can be found from:
Query Port Number
Change the port number using which you want to connect
[[email protected] ~]$ nslookup -port 56 tecmint.com Server: tecmint.com Address: 50.16.76.239#53 Name: 56 Address: 14.13.253.12
Read Also : 8 Nslookup Commands
44. Command: dig
dig is a tool for querying DNS nameservers for information about host addresses, mail exchanges, nameservers, and related information. This tool can be used from any Linux (Unix) or Macintosh OS X operating system. The most typical use of dig is to simply query a single host.
[[email protected] ~]$ dig tecmint.com ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.17.rc1.el6 <<>> tecmint.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<
Turn Off Comment Lines
[[email protected] ~]$ dig tecmint.com +nocomments ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.17.rc1.el6 <<>> tecmint.com +nocomments ;; global options: +cmd ;tecmint.com. IN A tecmint.com. 14400 IN A 40.216.66.239 ;; Query time: 418 msec ;; SERVER: 192.168.1.1#53(192.168.1.1) ;; WHEN: Sat Jun 29 13:53:22 2013 ;; MSG SIZE rcvd: 45
Turn Off Authority Section
[[email protected] ~]$ dig tecmint.com +noauthority ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.17.rc1.el6 <<>> tecmint.com +noauthority ;; global options: +cmd ;; Got answer: ;; ->>HEADER<
Turn Off Additional Section
[[email protected] ~]$ dig tecmint.com +noadditional ; <<>> DiG 9.9.2-P1 <<>> tecmint.com +noadditional ;; global options: +cmd ;; Got answer: ;; ->>HEADER<
Turn Off Stats Section
[[email protected] ~]$ dig tecmint.com +nostats ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.17.rc1.el6 <<>> tecmint.com +nostats ;; global options: +cmd ;; Got answer: ;; ->>HEADER<
Turn Off Answer Section
[[email protected] ~]$ dig tecmint.com +noanswer ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.17.rc1.el6 <<>> tecmint.com +noanswer ;; global options: +cmd ;; Got answer: ;; ->>HEADER<
Disable All Section at Once
[[email protected] ~]$ dig tecmint.com +noall ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.17.rc1.el6 <<>> tecmint.com +noall ;; global options: +cmd
Read Also : 10 Linux Dig Command Examples
45. Command: uptime
You have just connected to your Linux Server Machine and founds Something unusual or malicious, what you will do? Guessing…. NO, definitely not you could run uptime to verify what happened actually when the server was unattended.
[[email protected] ~]$ uptime 14:37:10 up 4:21, 2 users, load average: 0.00, 0.00, 0.04
46. Command: wall
one of the most important command for administrator, wall sends a message to everybody logged in with their mesg permission set to “yes“. The message can be given as an argument to wall, or it can be sent to wall’s standard input.
[[email protected] ~]$ wall "we will be going down for maintenance for one hour sharply at 03:30 pm" Broadcast message from [email protected] (pts/0) (Sat Jun 29 14:44:02 2013): we will be going down for maintenance for one hour sharply at 03:30 pm
47. command: mesg
Lets you control if people can use the “write” command, to send text to you over the screen.
mesg [n|y] n - prevents the message from others popping up on the screen. y – Allows messages to appear on your screen.
48. Command: write
Let you send text directly to the screen of another Linux machine if ‘mesg’ is ‘y’.
[[email protected] ~]$ write ravisaive
49. Command: talk
An enhancement to write command, talk command lets you talk to the logged in users.
[[email protected] ~]$ talk ravisaive
Note: If talk command is not installed, you can always apt or yum the required packages.
[[email protected] ~]$ yum install talk OR [[email protected] ~]$ apt-get install talk
50. Command: w
what command ‘w’ seems you funny? But actually it is not. t’s a command, even if it’s just one letter long! The command “w” is a combination of uptime and who commands given one immediately after the other, in that order.
[[email protected] ~]$ w 15:05:42 up 4:49, 3 users, load average: 0.02, 0.01, 0.00 USER TTY FROM [email protected] IDLE JCPU PCPU WHAT server tty7 :0 14:06 4:43m 1:42 0.08s pam: gdm-passwo server pts/0 :0.0 14:18 0.00s 0.23s 1.65s gnome-terminal server pts/1 :0.0 14:47 4:43 0.01s 0.01s bash
51. Command: rename
As the name suggests, this command rename files. rename will rename the specified files by replacing the first occurrence from the file name.
Give the file names a1, a2, a3, a4.....1213
Just type the command.
rename a1 a0 a? rename a1 a0 a??
52. Command: top
Displays the processes of CPU. This command refresh automatically, by default and continues to show CPU processes unless interrupt-instruction is given.
[[email protected] ~]$ top
top - 14:06:45 up 10 days, 20:57, 2 users, load average: 0.10, 0.16, 0.21
Tasks: 240 total, 1 running, 235 sleeping, 0 stopped, 4 zombie
%Cpu(s): 2.0 us, 0.5 sy, 0.0 ni, 97.5 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st
KiB Mem: 2028240 total, 1777848 used, 250392 free, 81804 buffers
KiB Swap: 3905532 total, 156748 used, 3748784 free, 381456 cached
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
23768 ravisaiv 20 0 1428m 571m 41m S 2.3 28.9 14:27.52 firefox
24182 ravisaiv 20 0 511m 132m 25m S 1.7 6.7 2:45.94 plugin-containe
26929 ravisaiv 20 0 5344 1432 972 R 0.7 0.1 0:00.07 top
24875 ravisaiv 20 0 263m 14m 10m S 0.3 0.7 0:02.76 lxterminal
1 root 20 0 3896 1928 1228 S 0.0 0.1 0:01.62 init
2 root 20 0 0 0 0 S 0.0 0.0 0:00.06 kthreadd
3 root 20 0 0 0 0 S 0.0 0.0 0:17.28 ksoftirqd/0
5 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 kworker/0:0H
7 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 kworker/u:0H
8 root rt 0 0 0 0 S 0.0 0.0 0:00.12 migration/0
9 root 20 0 0 0 0 S 0.0 0.0 0:00.00 rcu_bh
10 root 20 0 0 0 0 S 0.0 0.0 0:26.94 rcu_sched
11 root rt 0 0 0 0 S 0.0 0.0 0:01.95 watchdog/0
12 root rt 0 0 0 0 S 0.0 0.0 0:02.00 watchdog/1
13 root 20 0 0 0 0 S 0.0 0.0 0:17.80 ksoftirqd/1
14 root rt 0 0 0 0 S 0.0 0.0 0:00.12 migration/1
16 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 kworker/1:0H
17 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 cpuset
18 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 khelper
19 root 20 0 0 0 0 S 0.0 0.0 0:00.00 kdevtmpfs
20 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 netns
21 root 20 0 0 0 0 S 0.0 0.0 0:00.04 bdi-default
22 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 kintegrityd
23 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 kblockd
24 root 0 -20 0 0 0 S 0.0 0.0 0:00.00 ata_sff
Read Also : 12 TOP Command Examples
53. Command: mkfs.ext4
This command create a new ext4 file system on the specified device, if wrong device is followed after this command, the whole block will be wiped and formatted, hence it is suggested not to run this command unless and until you understand what you are doing.
Mkfs.ext4 /dev/sda1 (sda1 block will be formatted) mkfs.ext4 /dev/sdb1 (sdb1 block will be formatted)
Read More: What is Ext4 and How to Create and Convert
54. Command: vi/emacs/nano
vi (visual), emacs, nano are some of the most commonly used editors in Linux. They are used oftenly to edit text, configuration,… files. A quick guide to work around vi and nano is, emacs is a.
vi-editor
[[email protected] ~]$ touch a.txt (creates a text file a.txt) [[email protected] ~]$ vi a.txt (open a.txt with vi editor)
[press ‘i’ to enter insert mode, or you won’t be able to type-in anything]
echo "Hello" (your text here for the file)
- alt+x (exit insert mode, remember to keep some space between the last letter.
- ctrl+x command or your last word will be deleted).
- :wq! (saves the file, with the current text, remember ‘!’ is to override).
nano editor
[[email protected] ~]$ nano a.txt (open a.txt file to be edited with nano)
edit, with the content, required
ctrl +x (to close the editor). It will show output as:
Save modified buffer (ANSWERING "No" WILL DESTROY CHANGES) ? Y Yes N No ^C Cancel
Click ‘y’ to yes and enter file name, and you are done.
55. Command: rsync
Rsync copies files and has a -P switch for a progress bar. So if you have rsync installed, you could use a simple alias.
alias cp='rsync -aP'
Now try to copy a large file in terminal and see the output with remaining items, similar to a progress bar.
Moreover, Keeping and Maintaining backup is one of the most important and boring work a system administrator, needs to perform. Rsync is a very nice tool (there exists, several other) to create and maintain backup, in terminal.
[[email protected] ~]$ rsync -zvr IMG_5267/ copy/=33/ copy/=ok.jpg ~/Desktop/ sending incremental file list IMG_5267 copy=33 copy=ok.jpg sent 2883830 bytes received 31 bytes 5767722.00 bytes/sec total size is 2882771 speedup is 1.00
Note: -z for compression, -v for verbose and -r for recursive.
56. Command: free
Keeping track of memory and resources is as much important, as any other task performed by an administrator, and ‘free‘ command comes to rescue here.
Current Usage Status of Memory
[[email protected] ~]$ free
total used free shared buffers cached
Mem: 2028240 1788272 239968 0 69468 363716
-/+ buffers/cache: 1355088 673152
Swap: 3905532 157076 3748456
Tuned Output in KB, or MB, or GB
[[email protected] ~]$ free -b
total used free shared buffers cached
Mem: 2076917760 1838272512 238645248 0 71348224 372670464
-/+ buffers/cache: 1394253824 682663936
Swap: 3999264768 160845824 3838418944
[[email protected] ~]$ free -k
total used free shared buffers cached
Mem: 2028240 1801484 226756 0 69948 363704
-/+ buffers/cache: 1367832 660408
Swap: 3905532 157076 3748456
[[email protected] ~]$ free -m
total used free shared buffers cached
Mem: 1980 1762 218 0 68 355
-/+ buffers/cache: 1338 641
Swap: 3813 153 3660
[[email protected] ~]$ free -g
total used free shared buffers cached
Mem: 1 1 0 0 0 0
-/+ buffers/cache: 1 0
Swap: 3 0 3
Check Current Usage in Human Readable Format
[[email protected] ~]$ free -h
total used free shared buffers cached
Mem: 1.9G 1.7G 208M 0B 68M 355M
-/+ buffers/cache: 1.3G 632M
Swap: 3.7G 153M 3.6G
Check Status Contineously After Regular Interval
[[email protected] ~]$ free -s 3
total used free shared buffers cached
Mem: 2028240 1824096 204144 0 70708 364180
-/+ buffers/cache: 1389208 639032
Swap: 3905532 157076 3748456
total used free shared buffers cached
Mem: 2028240 1824192 204048 0 70716 364212
-/+ buffers/cache: 1389264 638976
Swap: 3905532 157076 3748456
Read Also : 10 Examples of Free Command
57. Command: mysqldump
Ok till now you would have understood what this command actually stands for, from the name of this command.mysqldump commands dumps (backups) all or a particular database data into a given a file.For example,
[[email protected] ~]$ mysqldump -u root -p --all-databases > /home/server/Desktop/backupfile.sql
Note: mysqldump requires mysql to be running and correct password for authorisation. We have covered some useful “mysqldump” commands at Database Backup with mysqldump Command
58. Command: mkpasswd
Make a hard-to-guess, random password of the length as specified.
[[email protected] ~]$ mkpasswd -l 10 zI4+Ybqfx9
[[email protected] ~]$ mkpasswd -l 20 w0Pr7aqKk&hmbmqdrlmk
Note: -l 10 generates a random password of 10 characters while -l 20 generates a password of character 20, it could be set to anything to get desired result. This command is very useful and implemented in scripting language oftenly to generate random passwords. You might need to yum or apt the ‘expect’ package to use this command.
[[email protected] ~]# yum install expect OR [[email protected] ~]# apt-get install expect
59. Command: paste
Merge two or more text files on lines using. Example. If the content of file1 was:
1 2 3 and file2 was: a b c d the resulting file3 would be: 1 a 2 b 3 c d
60.Command: lsof
lsof stands for “list open files” and displays all the files that your system has currently opened. It’s very useful to figure out which processes uses a certain file, or to display all the files for a single process. Some useful 10 lsof Command examples, you might be interested in reading.
[[email protected] ~]$ lsof COMMAND PID TID USER FD TYPE DEVICE SIZE/OFF NODE NAME init 1 root cwd DIR 8,1 4096 2 / init 1 root rtd DIR 8,1 4096 2 / init 1 root txt REG 8,1 227432 395571 /sbin/init init 1 root mem REG 8,1 47080 263023 /lib/i386-linux-gnu/libnss_files-2.17.so init 1 root mem REG 8,1 42672 270178 /lib/i386-linux-gnu/libnss_nis-2.17.so init 1 root mem REG 8,1 87940 270187 /lib/i386-linux-gnu/libnsl-2.17.so init 1 root mem REG 8,1 30560 263021 /lib/i386-linux-gnu/libnss_compat-2.17.so init 1 root mem REG 8,1 124637 270176 /lib/i386-linux-gnu/libpthread-2.17.so init 1 root mem REG 8,1 1770984 266166 /lib/i386-linux-gnu/libc-2.17.so init 1 root mem REG 8,1 30696 262824 /lib/i386-linux-gnu/librt-2.17.so init 1 root mem REG 8,1 34392 262867 /lib/i386-linux-gnu/libjson.so.0.1.0 init 1 root mem REG 8,1 296792 262889 /lib/i386-linux-gnu/libdbus-1.so.3.7.2 init 1 root mem REG 8,1 34168 262840 /lib/i386-linux-gnu/libnih-dbus.so.1.0.0 init 1 root mem REG 8,1 95616 262848 /lib/i386-linux-gnu/libnih.so.1.0.0 init 1 root mem REG 8,1 134376 270186 /lib/i386-linux-gnu/ld-2.17.so init 1 root 0u CHR 1,3 0t0 1035 /dev/null init 1 root 1u CHR 1,3 0t0 1035 /dev/null init 1 root 2u CHR 1,3 0t0 1035 /dev/null init 1 root 3r FIFO 0,8 0t0 1714 pipe init 1 root 4w FIFO 0,8 0t0 1714 pipe init 1 root 5r 0000 0,9 0 6245 anon_inode init 1 root 6r 0000 0,9 0 6245 anon_inode init 1 root 7u unix 0xf5e91f80 0t0 8192 @/com/ubuntu/upstart init 1 root 8w REG 8,1 3916 394 /var/log/upstart/teamviewerd.log.1 (deleted)
This is not the end, a System Administrator does a lot of stuff, to provide you such a nice interface, upon which you work. System Administration is actually an art of learning and implementing in a very much perfect way. We will try to get you with all other necessary stuff which a linux professional must learn, linux in its basic actually itself, is a process of learning and learning. Your good words are always sought, which encourages us to put in more effort to give you a knowledgeable article. “Like and share Us, to help Us Spread”.
Source: tecmint.com
